자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can cause a lot of trouble. This can be an opportunity to upgrade your windows to energy efficient or insulated ones, and reap advantages like improved comfort, higher resale value and reduced utility bills.

You can do it yourself for less than what it would cost to hire an expert. It requires the right tools and only an hour or two of your time.

Glass

Replace your old single-paned windows using tempered or insulation glass to improve the efficiency of your energy, reduce noise, and maintain the historical integrity of your home's older. Most homeowners with basic hand tools can replace windows with ease. You'll also require an additional window pane, glazier's suggestions, pliers, and latex glaze putty. If you need to you may use a heating gun to warm the old putty. Before starting, wear protective gloves and goggles since working with broken glass may cause injuries.

Begin by removing any remaining broken pieces of glass. It is best to use pliers for this, but a flathead can be used equally. Then, use a wooden chisel or putty knife take the remainder of the old putty around the frame and the sash. Work slowly and carefully and be careful not to break the current window sash. It is a good idea to do this on a stable ladder instead of the ground and to have someone stand below the sash to help keep it steady.

Prepare the window frame to accommodate the new pane once you have removed the old glue. Take measurements of the width and height of the opening for the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be taken to an hardware or home centers store to get cut a piece of glass that is in stock to the correct size. Alternately, you can cut the glass yourself if have the right tools.

After installing the new glass, apply a small amount of caulking to the edge. This will make the glass weatherproof. Then, you can install a glazier's pointing on the frame's opposite side to secure the pane into the right place. The points shouldn't be so tight that they cause friction between the sash and the frame however they shouldn't be loose.

Before putting the putty on, make sure to knead it until it is smooth and free of lumps. Then make it into pencil-sized strips. Apply the first strip to the corner of the frame. Work from corner to corner and ensure that it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces that help secure glass into the frame of a window without scratching or damaging the delicate surface. Understanding how to use these hidden little helpers is easy and could save you money on professional installation or the cost of new glass.

After the old putty as well as the glazier's point are gone and the frame is thoroughly cleaned using a utility knife to remove any remaining residue. Lightly sand the wood into the rabbet grooves to smooth out rough areas. If you do sand your wood, ensure you protect it with painter's tape to avoid accidental damage.

Measure the empty frame's dimensions and note down precise measurements. These dimensions can be taken to a home center or hardware store and the new pane will be cut a bit smaller. This will ensure a secure fit and will allow room for expansion and contraction.

Place the new pane in the frame and push it in place with your hand. Make use of the chisel's point or the edge of the putty blade to smudge the glazier's points, as illustrated in Figure 11. When you're done, they should be level with the top edge of the pane. the shoulders of the points should be below the rabbet's rim groove.

Apply a thin bead of glazing compound over the edges of the new glass and in the rabbet grooves, to seal and protect them. Allow this to dry and cure completely.

Once the glazing compound has dried it's time to put in the new window sash. First, coat the wood with an even layer of linseed. This will stop the new putty from taking in the moisture and deteriorating and cracking with time. Apply the coating using a brush this coat, or the tip of the blade. Then, use the chisel that is on the back of the tool or the back of the putty handle to gently hit the new sash, or glazier's point into the rabbet grooves. Repeat this process at intervals of 10 inches around the frame.

Putty

A baseball thrown at you, an errant rock or a falling branch can cause a window replacement companies to crack or break. The majority of windows can be repaired easily by simply putting in a fresh piece. The glass is held in place using a small metal clip called the glazier's pointed and putty, which is often called glazing compound. Before installing a replacement glass for windows pane, Double Glazed Window Replacement first remove the old one and clean the area using an abrasive and an abrasive scraper that is a pull type or the wood chisel. Wear gloves and safety glasses while you do this work. If the window is glued to the frame, you'll need make use of a heat gun to soften the adhesive prior to taking it off.

If you're planning to install your original sash, you must remove the molding that supports the old pane. Then you can sand the sash down to make sure it's flat and ready to be re-caulked. After the sash has been re-installed, apply a new silicone caulk around the glass to ensure it won't leak or discolor as time passes.

Remove the glazing points in the rabbets. These are the grooves in the sash, where the glass replacement for window is. If they're difficult to chisel, use a hand [empty] tool such as a heatgun over them for a few minutes to soften them. When using a heated tool, be sure to not scratch the sash or its railings.

Prepare the bed for your new pane by removing the old glaze and putty. Roll a rope of glazing compound between your hands, and form it to be about 1/2-inch thick. Then, press it into the rabbets in which the glass will be. The glass must rest against the putty on both sides. If needed gently tap your glass into the rabbet with your thumb.

If the new pane is cracked, you can use a silicone caulk or glass glue that is based on solvents to seal the crack prior to pressing it into the sash. Otherwise, you'll need to putty over the crack to form an airtight seal and keep water out. Once the putty is dry remove the oily film off the glass and let it dry completely before you paint. If you paint before the putty has completely dry, it won't create an effective seal and could leak or discolor in time.

Paint

If you've experienced a broken window pane, you may be concerned about the expense of a new one. The truth is, replacing a single piece of glass doesn't have to be expensive even if you do it your own. Even a double-paned window can be replaced for a fraction of what it costs a professional.

If you are working on a large-sized Window Glass Replacements Near Me, make sure that it is securely attached to the frame. By using the correct tools and techniques you can make this task relatively easy and speedy.

When you are ready to begin taking down the old window pane. Pry out the glazing points made of metal that are attached to it. They are basically tiny metal triangles which function as "nails" that keep the window in place in the wood frame. They are placed beneath a layer of glazing putty, which is then cured to form a solid, molded wedge that secures the window in place and hides the window's points.

Once you have the old pane taken away Clean up the frame and wood. Scrape off any old paint, and sand the rabbet grooves in which the glazing points were placed. Sand them down to bare wooden surfaces so you can paint the frames with the same color. After the sanding process, apply a coat of flax oil on the wood that is not sanded down to extend the life of the frame.

Next, measure the dimensions of the window opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you get a precise size for the new pane. This will also allow for expansion and contraction of the glass in times of seasonal changes. You can bring these measurements to a hardware store or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.