자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a loose door hinge can be a manageable task for the majority of homeowners. But, if the screw holes are stripped and won't hold screws you might have to use dowels and wood glue before you can reinstall the hinge.

Brush away any surface corrosion. This will help to keep the dowels in their place and provide an adequate base for them to grip onto.

Take off the Hinges

Many hinges for doors can be removed, making it simpler to move doors from one side of the frame to the other side or take the entire door off when needed. The removal of the hinges is easy for anyone with a little patience, although you have to know how to do it right.

If the hinges have been painted, you'll need to take off the paint prior to trying to remove the pins. If you don't, the paint will flake off and scratch the door when you attempt to lift it. To break the paint seal put the hinges in a stainless steel pan and fill the pan with water until the hinges are completely submerged. Allow the hinges to sit in the pan for about 30 minutes. The heat from the water should soften the paint and make it easier to get rid of the pins.

After the pins are loosening then you can remove the hinges from the frame and door. You can use a screwdriver to get the job done, however it is recommended to use a magnetic screwdriver for this task. This type cost of replacing window hinges screwdriver was created to grab screws made of steel and will make the project speed up.

It is a good idea to spray some lubricant on the hinges prior to trying to remove them. A simple lubricant will allow you accelerate the process and make the removal of pins and screws more easily. This kind of lubricant can be found in most hardware stores as well as home improvement shops.

The number of hinges needed will also depend on what type of door you have, and how it's set up. Doors with solid cores and heavy weights will require more hinges whereas lighter and hollow-cored doors may only need two or three.

Understanding the various types of hinges can help you determine which one is best for your situation. The hinges on the exterior are designed to support the weight of a door, whereas interior hinges need to be able to support heavier loads.

Reattaching the Hinges

Over time, a door window hinge repair costs can become loose and start to sag or hang crookedly. This can cause problems however, it's usually simple to fix. A simple tightening can solve the issue. If the screw holes have been ripped out, it can be difficult to fix. Fortunately, there is a trick to make these holes back to their original size that uses a wood dowel.

Start by drilling the old hole using a drill bit close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length the same as the screw to ensure a tight fit. Install the screw again and tighten it until you are satisfied with the tightness. If the door does not stop bind up, insert a second dowel to the gap. Repeat the procedure. Be sure to shut the door slowly in order to verify the clearances at the perimeter after each adjustment.

Another option is to just use an old-fashioned wood plug instead of dowel. This will work equally well, but may take a little longer to put in. You can tap in a piece of wood which has been cut to the right size. If you don't have a tool for woodworking, you can also try using toothpicks or wooden matches.

Once you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the head of the screw smaller, so that it doesn't rub against the edge of the door when it's open and closed. This will make it easier to tighten the screws before reinstalling hinges.

After installing the hinge, apply lubrication to the hinge using dry lubricant. This will help to prevent it from becoming stuck in the future. You can use products like PB Blaster and Liquid Wrench. You should apply a thin coat and give it about 15 minutes to fully penetrate the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace your hinges, you can try a few easy fixes. The first step is to ensure that the screws securing the hinge plate to the door frame are tight. If they're loose, tighten them by using a drill or screwdriver. Be careful not to tighten your screws so much that they start to cause gaps at the trim joints, or even worse remove the threads.

If the problem is that the hinge plates are breaking away from the door and jamb, you can reattach them by gluing wood glue to the back of the plates and then inserting toothpicks or wooden dowels into the holes. The dowels or toothpicks give a solid foundation for the screws and keep the plates from moving when you drive them into place. Let the glue dry before attaching the hinge.

Another reason for hinges that are loose is that the screws are stripped or gone. This problem can be fixed by replacing the screws. Use a drill bit that is similar to the size of the screw hole to avoid drilling into the hinge or jamb.

Close the door after you've reattached the hinge and measure the gap between the frame and the door. It should be around the thickness of a nickel all the way around or less if there's an existing gap created by a previous door that was not properly hang. If the hinges were set up properly, this shouldn't be a problem.

If you find that the hinges are still loose, try putting a thicker hinge shim between the hinge plate and the mounting surface, to create an extra inch of space. You can also take off the hinge pin, then pound it down with a powerful hammer to tighten it or use an entirely new hinge. You can also lubricate your hinges with mineral or jojoba oil to decrease friction hinges for timber windows and help them hold their position. Regularly lubricating your hinges will aid in keeping them from becoming stiff or squeaky, and will also prolong their lifespan.

Cleaning the Hinges

The constant movement of a hinge creates friction, which attracts dust particles. These particles can become stuck and accumulate in the moving parts of door hinges if they are not cleaned and lubricated regularly. The hinge will get stiff and creaky and its appearance could rapidly diminish. Regular cleaning, lubrication, and inspections can maintain the integrity of a door's hinges and ensure their proper function.

Examine the hinges for corrosion. If the rust has corroded to the point of destroying surface of the barrel or screw holes, you'll have to replace the hinges. If you are able to save the hinges, you should first clean off any loose rust with steel wool and a wire brush. Apply a commercial rust-removing product or a homemade solution such as lemon juice to the hinge. Let the solution that removes rust remain on the hinges for several minutes to penetrate and dissolve any remaining rust.

If you don't wish to spend the money and time replacing aluminium windows hinges, tightening the screws will restore the hinges' functionality. If you have stripped the screw holes, however, it may be necessary to attach an wooden dowel or shim to the hinge. Wooden dowels come in round rods that vary in lengths and sizes. You can find them at home improvement stores or woodworking supply shops, or on the internet.

A shim can also be made from a piece of plastic or metal, based on the kind of hinge you've got. To make a dowel cut a wooden dowel to the desired length. You can then dip the dowel into a carpenter's glue and insert it into the cut hole and let the glue hold the dowel in place.

Before you begin cleaning the hinges, place down a towel or a paper towel to shield flooring and other surfaces from accidental spills and drips. After the area has been secured and dry, clean the hinges using a soft cloth or sponge coated with a mild cleaner or vinegar to remove dirt, grime, and tarnish. You can make use of a small or toothbrush brush to reach difficult-to-reach places in crevices or tight areas.