자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

Replacing a damaged window handle is a simple process and with the right tools it can be accomplished quite quickly. It is important to know the type of handle you have and the spindle's size before you purchase a replacement.

Older uPVC windows have handles with cockspurs, which have an extension spur that can the lock of a wedge cockspur striker plate. They can be left or right-handed and need to be replaced with the same handle.

What kind of lock or handle do I have

There are many kinds of upvc window handles and locks, each with their own benefits and purposes. The type of handle that you have will determine whether or not your locking mechanism is efficient and if it is easy to open the windows. With time and regular use, upvc window handles are prone to wear or damage. out, making them less effective and secure. In some cases they may even fall off completely. If you find that your window handles have been removed, it's crucial to repair them as quickly as you can. This will help prevent burglaries, and keep your house safe.

The good news is that replacing your upvc window handles is a fairly simple job that can be completed by nearly anyone. You'll need a few basic tools, but with appropriate knowledge, it's a straightforward process that should only take a couple of minutes. You will need to be aware of the type of lock or handle you have on your window. This will allow you to choose the right glass replacement for window.

Inline Espagnolette Handles

These are the most commonly used type of upvc handle and are usually placed on the outside of your window. They are flat and feature an opening that engages the locking mechanism of the window frame. Inline upvc handles also have a spindle that runs through the centre of the handle and then into the frame of the window to activate the latch.

Cockspur Handles

They are usually found on older uPVC windows and have an distinctive hook-shaped design. Cockspur handles are held to the window frame by a single screw and are less secure than other kinds of window handle.

Handles that can tilt and turn

The tilt and turn handles differ from other handles made of upvc in that they can be rotated to open the window and then tilted into the window to allow air circulation. They feature a 7mm spindle at the back and are available in left and right-handed versions.

When purchasing replacement handles made of upvc it is essential to check the spindle length because not all handles are the same size. Drop something in the middle of the hole to test the length. This is the maximum size of spindle that will fit into your windows.

What is the spindle?

uPVC window handles function similarly as doors, with the user turning the handle to operate an opening inside the frame. The window is then opened and closed. However, sometimes handles can be damaged, especially when they are used frequently or exposed to harsh weather conditions. You may need to replace the handles on your uPVC window if they're not operating properly.

There are many different kinds of uPVC handles that are available, comprising Espag, Cockspur and Spaded handles. They are designed to fit into the uPVC frames in a variety of ways. Each handle uses a specific spindle to lock the mechanism fitted to the window. This is why it is essential to know what kind of handle you have on your uPVC window to find the right replacement for it.

You can find out what kind of uPVC handle you are using by looking at the base section of your handle. A snap-in cover is over the screw that holds the handle's base in position. When you remove this cover, you will be able see the screw that holds the handle base in position. After both screws have been removed, you should be capable of pulling the handle away from the uPVC window.

After taking off the uPVC handle, carefully remove it from the locking mechanism. Take careful note of the length of the spindle, as you'll need to make sure that you buy a replacement that has the same length as your original handle and locking mechanism.

The spindle wears out and cannot operate the locking mechanism. This can be due to damage caused by constant use, a loosening of the locking mechanism or even corrosion that occurs over time. If this occurs, you will have to replace both the window handle and the locking mechanism to restore the full functionality of your uPVC Windows.

How do I remove the old handle?

Window handles can be damaged or destroyed over time. It is essential to fix them as quickly a possible to ensure your safety. It is good to know that replacing a worn or damaged handle is a relatively simple job that can be accomplished in just over a minute and doesn't require any special tools.

To remove the old handle, you first need to remove the screw that is located at the bottom of the handle. Once this is removed the handle can be removed from the base section. A second screw will be situated at the base of the handle. It can also be removed. Once these two screws have been removed, the handle can be removed from the base of the window.

After removing the handle and fixing holes, align the holes of the new handle to the holes that are already in the window frame. There may be a tiny sticker or caps on the new handle, so remove these if necessary and then put the handle in place. It is crucial to verify that the handle works once it is put in place. Turn the handle over and make sure that the lock mechanism is in place.

Espag handles have spindles that protrude out of the handle and slots into the multipoint locking mechanism on the window frame. Cadenza windows have a blade with cut-outs that slot into the lock mechanism, while Cockspur handles have a long nose that hooks over the frame's outer or transom bar cross-member inside the window.

After you have put in the new handle, insert the spindle into the window lock and tighten it. Replace the snap-in cover and screw cap (if necessary) once the handle has been firmly fixed. The handle is now ready for use to use, so try opening and closing the window several times to check that it works correctly and securely.

How do I put in the new handle?

The process of changing your window handle made of uPVC isn't difficult, and the process is actually very simple. All you need is a screwdriver and a little bit of patience. First, ensure that the handle is not locked. Remove any screws visible. You can also replace them with screw caps. After removing the handle, you will need to note the length of the spindle that extends from the back. This is crucial as it will determine the type of handle you'll require to purchase.

Espagnolette handles on uPVC are the most popular type of handle. The spindle passes through the handle to operate the locking mechanism within the window frame. When the handle is turned it releases the latch on the window, allowing it to open. During regular use and time, handles for espagnolette may be damaged.

Cadenza handles are a second type of uPVC window handle, which is typically used on tilt and turn windows. They feature a protruding blade that operates a multiple-point locking mechanism inside the window. They are more secure than espagnolette handles because they are able to open from the inside. You can replace them with the same method that you would for espagnolette handles however, make sure that the new handle is not angled and flat.

Once you've decided on the right handle for you You can simply place the new handle with the screw holes, and then screw it into place. After that, you should put the screw covers back on and verify that the new handle is working correctly. You can perform this by dragging the handle back and forth from the locked position to the unlocked one a few time. It is possible to contact an expert to determine how you can fix any problems. They are often able to advise you on the best solution to resolve the issue in a fast and efficient way.