자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

Replacing a damaged or broken window handle is a easy task and with the right tools it can be done quite quickly. However, it is essential to know your type of handle and its spindle's length prior buying the replacement sash windows.

Older uPVC window handles have a spur which extends and is locked over the cockspur wedge striker. These can be right-handed or left-handed and must be compatible when replaced.

What type of lock and handle do I have?

There are many window locks and handles made from upvc each with their particular advantages and uses. The type of handle that you choose will determine if your locking mechanism is effective and if it's easy to open windows. With time and regular use the upvc handles that are on your windows can be damaged and worn out. This makes them less secure and less effective. In some instances, they may even fall off completely. It is crucial to fix your window handles made of upvc as soon as you see they are falling off. This will help avoid burglaries and keep your home safe.

The good news is that replacing your upvc window handles is a simple task that can be done by almost anyone. You will need a few tools, but with right knowledge, it is a straightforward process that should take only a couple of minutes. To begin, you will need to identify the type of handle and lock you have on your upvc window to help you to find the ideal replacement.

Inline Espagnolette Handles

They are usually found on the side of the window. They are flat in design and come with a latch that connects to the locking mechanism of the window frame when turned. Inline upvc handles also come with a spindle that goes through the center of the handle, and into the frame of the window to activate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and have an unusual hook-shaped design. Cockspur handles have one screw that is used to secure the handle to the window frame and are not as secure as other kinds of window handles.

Handles that tilt and turn

As opposed to the other upvc handles the tilt and turn handles can be turned to open the window, and turned inwards to allow to let air flow in. They have a 7mm spindle on the back and are available in left and right-handed versions.

When buying replacement upvc handles, it is important to measure the spindle's length since not all of them are the same size. Drop something in the middle of the hole to test the length. This is the longest spindle length that will fit your window.

What is spindles?

uPVC window handles function in a similar manner like doors. By turning the handle, you are able to activate a latch inside the frame. The window can then be opened and shut. The handles could be damaged, especially if they're used frequently or subjected to harsh conditions. This could mean that you have to replace your uPVC windows handles as they may not operate the window properly anymore.

There are many different types of uPVC handle options, including Espag, Cockspur, and Spaded handles. They are designed in a variety of ways to fit into uPVC frames. Each handle type utilizes a different spindle to lock the window mechanism. It is crucial to know the type of handle you have installed on your uPVC windows so that you can replace it with the right one.

The base section of the handle will inform you what type of uPVC it is. There should be a "snap in' cover over one screw that holds the handle's base in the correct position. When you remove this cover and you'll be able to see the second screw that holds the handle base in position. Once both screws have been removed then you should be able to remove the handle from the uPVC.

After you have removed the uPVC window handle you need to carefully remove the old spindle from the locking mechanism. Be sure to note the length of the spindle since you'll need to ensure that you buy one that is the same length as the original handle and locking mechanism.

The primary issue with uPVC window handle problems is that the spindle becomes worn out and can no longer function properly with the locking mechanism. This can be due to damage from constant use or a loosening of the locking mechanism, or even corrosion over time. If this happens, you will have to replace both the window handle and the locking mechanism in order to restore the full functionality of your uPVC Windows.

How do I get rid of the handle that was previously attached?

Window handles can be damaged or broken over time. It is important to fix them as soon as possible to ensure your security. It is easy to replace a damaged or worn handle. The job can be completed in less than a minute without the need for special tools.

To remove the old handle, first remove the screw that is located at the bottom of the handle. After this screw is removed, the handle can be pulled away from the base. There will be another screw located at the bottom of the handle's base and this can be removed too. Once these two screws are removed, the handle can be removed from the window's base.

After removing the old handle and align the fixing holes of the new handle to the holes that are already in the window frame. There may be a little cap or sticker on the new handle, so take off these if necessary and then screw the handle into place. Once the handle is in place, it is crucial to verify that it is working by turning the handle and ensuring that the lock mechanism is activated.

Espag handles feature a spindle which protrudes out of the handle and slot into the multipoint locking mechanism that is on the frame of the window. Cadenza windows have a blade with cutouts that fit into the lock mechanism. Cockspur handles are long and hook over the frame of the window or the transom bar crossmember.

Once you have installed the new handle, slide the spindle into the window lock and tighten it. Once the handle is firmly fixed and secured, replace the snap-in cover and screw cap (if necessary). The handle is now ready for use by opening and closing the window a few times to ensure that it is working well and securely.

How do I install the new handle?

Switching your uPVC window handle isn't difficult and the process is quite simple. All you need is a screwdriver, and a bit of patience. The first step is make sure that the handle you have previously used is not locked and then remove any screws that are visible, you can replace them with screw caps if needed. After the handle has been removed, you need to make an outline of the length of the spindle that protrudes from the back of the handle. This is vital because it will determine the kind of handle you will need to buy.

Espagnolette handles are the most commonly used kind of handle that is used on uPVC windows. They feature a spindle that runs through the handle and acts as a locking mechanism within the window frame. When the handle is turned, it releases the latch on the window, allowing it to open. With time and regular use, espagnolette handles could be damaged or damaged which is why it is essential to locate a replacement.

Cadenza handles are a form of uPVC handle that is typically employed with tilt and turn windows. They feature an extended blade that works the multipoint locking mechanism inside the window. They are generally more secure than espagnolette handles as they are only accessible from the inside. They can be replaced using the same method that you would for espagnolette handles however, ensure that the new handle is not angled and flat.

Once you have selected the correct handle, simply align the new handle to existing screw holes prior to fixing it with screws. After that, you can put the screws on and test your new handle. This is accomplished by moving the handle from locked to the unlocked position and then back to the locked position several times. It might be worthwhile to speak with an expert to determine if you can resolve any issues. They will often be able to guide you on the best approach to solve the issue in a fast and efficient manner.