자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can be a source of frustration. This could be an opportunity to upgrade your windows to energy efficient or insulated ones, and reap benefits such as improved comfort, higher resale value and reduced utility bills.

You can do it yourself for a less than what it would cost to employ an expert. It requires the right equipment and an hour or two of your time.

Glass

If your single pane windows glass replacement are old damaged, cracked or deteriorating replacing them with more modern glass that is tempered or insulated can increase energy efficiency and decrease noise while also preserving the historic integrity of older homes. Most homeowners with basic hand tools can replace a window pane. In addition to a replacement windows and Doors pane, the following items are required for the replacement process: latex glazing putty pliers, glazier's points and the use of a heat gun to warm the old putty if required. Wear safety glasses and gloves prior to beginning. Working with broken glass could cause serious injuries.

Remove any broken glass pieces that remain. It is recommended to use pliers for this, but a flathead can be used equally. After that, use a wood chisel or putty knife to take the remainder of the old putty from around the frame and sash. Work slowly and carefully and be careful not to break the current window sash. This can be done best on a ladder, not on the ground. Also, have someone on the ground to ensure it is held steady.

Prepare the window frame to receive the new pane once you have removed the old glue. Measure the width and height of the opening for the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be sent to an hardware or home centers store to have a piece cut of glass stock to the proper size. You can cut the glass yourself if you possess the right tools.

After installing the new glass, apply caulking to the edge. This will make the glass weatherproof. Install a glazier's point on both sides of the frame. This will help secure the pane. The points shouldn't be too tight that they cause friction between the sash and the frame however they shouldn't be too loose.

Before applying the putty to the surface, knead thoroughly until it becomes soft and free of lumps. Cut it into pencil-sized pieces. The first strip should be placed in the corner of the frame, moving from one corner to another so that it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal that help secure the glass into the window frame without damaging the delicate surface. It's simple to learn how to use this secret tool, and you'll save money on the cost of a professional installation.

After the old putty and glazier's points are removed Clean the frame thoroughly with a knife to get rid of any remaining traces. Lightly sand the wood into the rabbet grooves to smooth out rough areas. If you do sand your wood, be sure to protect it by using painter's tape to prevent accidental damage.

Take the dimensions of the frame and record precise measurements. Bring these measurements to a hardware store or home center and have the new pane cut smaller than the frame's opening. This will ensure a tight fit and will allow room for expansion and contraction.

Place the new pane into the frame and push it into the frame by using your hands. Utilize the point of the chisel or the back of the putty knife to tap in the glaziers' points as shown in Figure 11. The glazier's points should be flush against the top edge of your pane, and the raised shoulders should be just below the lip.

Apply a thin layer glazing compound on the rabbet grooves and the edges of the glass. This will seal and protect the edges. Allow it to dry completely and cure.

Install the new window sash after the glazing compound has dried. The first step is to coat the wood with a heavy coat of linseed oil. This will stop the new putty from soaking up moisture and drying out and cracking over time. Apply the coating using a brush this coat, or the point of the putty blade. Then, use the chisel that is on the back of the putty tool or the back of the handle to gently hit the new sash, or glazier's point into the rabbet grooves. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball that is thrown or a rock that is errant or a fallen branch can cause a window pane to crack or break. The majority of windows can be replaced by simply putting in a fresh piece. The glass is held in place by a small metal clip, also known as a glazier's point and putty. This compound is also called glazing compound. Before installing a new pane, first get rid of the old one and clean the area with a rag and the pull-type paint scraper or an abrasive wood chisel. Wear safety glasses and gloves while doing this work. You'll need a heat gun if the window is glued to the frame.

If you're planning to install the original sash, gently remove any molding pieces that are used to secure the old pane. Then you can sand the sash down to ensure it's level and ready for new caulk. Once the sash is installed and sanded, apply a fresh caulk made of silicone around the glass to ensure it won't leak or discolor in time.

Remove the glazing points from the rabbets. These are the grooves in the sash, which is where the glass is located. If they're difficult to work out, try holding a hand tool like a heat gun over them to soften them up first. If you're using a heat gun, be careful not to cause damage to the sash or its railings by using the tool too tightly.

Create a bed for your new pane after removing the old glaze and putty. Roll a rope with glazing compound between your fingers, and then make it about 1/2 inch thick. Then, press it into the rabbets, where the glass will be. The glass must rest against the putty on both sides. If necessary, lightly tap your glass into the rabbet with your thumb.

If the new pane is cracked, you can cover it with a solvent-based glass glue or silicone caulk before pressing it into the sash. In other cases, you'll need to apply putty over the crack to form an impervious seal to keep water out. When the putty dries, clean the oily film off the glass using a rag and allow it to dry completely before painting. Paint before the putty has dried completely. It won't make a strong seal and could leak or discolor with time.

Paint

You may be concerned about replacing a broken piece of glass. But the truth is that replacing one glass pane does not have to break the bank when you do it yourself. In fact, even a double-pane window can be replaced at a fraction of the cost of an expert.

If you're working with large glass windows replacements near me, first make sure it is securely attached to the frame. This can be done relatively easy and fast using the proper tools and techniques.

When you are ready to start taking down the old window pane. Remove the metal glazing points that are attached to it. These are tiny triangles of metal that act as "nails" to hold the window in place. They are placed under a glaze putty or bead that hardens to an unbreakable wedge that holds the wood frame in place and hides the points.

Once you have the old pane removed Clean up the frame and wood. Scrape off any paint that has been used and sand down the rabbet grooves where the glazing points were placed. These should be sanded to bare wood so that you can paint them the same color as the rest of the frame. After sanding the wood then apply a layer of flax oil. This will help extend its life.

Next, measure the dimensions of the window opening. It is necessary to take horizontal and vertical measurements of the entire opening, and also the thickness of the old pane. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass in times of seasonal change. Take these dimensions to your local hardware or home improvement store and ask them to cut you the glass window replacement cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.